They raged against the dying of the neon, sombrero-shaped light. ¶ Institutions belong to the community, and the Austinites and Texas Exes that strolled the Drag for years on their way to that Tex-Mex beacon weren’t satisfied to let the crispy tacos and combo plates go gently into that good night. It’s a rarity on the periphery of campus, an area that has seen many cafes, taverns, and movie theaters open and close amid a few mainstays. UT students had come and gone, but they all remembered the same place, same feel, and same melted yellow cheese. This past summer, when the news that one of these institutions, El Patio, would be closing its doors after 66 years, there was a multi-generational outcry. NOTE: (1) Mapping of 4101 to 4126 is the same as the alphabetic addressing of Macro Arguments section e.g., the statement X1.3 sets variable #4124 to 1.3.Restaurant isn’t just a restaurant after six-plus decades-it’s an institution. Programmable coolant positions for tools 1 through 200 Maximum recorded vibrations of tools 1 through 200 Maximum axis loads for C, U, V, W, and T-axes respectively Spindle load with Haas vector drive (read only) Maximum axis loads for X, Y, Z, A, and B Axes, respectivelyįiltered analog to digital inputs (read only) General-purpose variables saved on power off This is useful for debugging macro processing within NC programs. When a block delete token "/" is used, even if Block Delete mode is not active, the line will block look ahead. The program is used as a sub-program when Block Delete is off. Makes the sub-program a main program when BLOCK DELETE is on. While Block Delete mode is active, the control does not execute the blocks marked with a / character. Press BLOCK DELETE to enter the Block Delete mode. Use a / character at the beginning of the program blocks that you want to skip. For additional information, refer to G103 Limit Block Look-Ahead (Group 00)īlock Delete mode lets you selectively skip blocks of code. The Pnnaddress code in G103 specifies how far ahead the control is allowed to look. G103 limits how far ahead the control looks at blocks of code. This lets the control transition smoothly from one motion to the next. The Haas control uses block look-ahead to read and prepare for blocks of code that come after the current block of code. Probing - Using a probe enhances the capabilities of the machine, some examples are:Ī) Profiling of a part to determine unknown dimensions for machining.ī) Tool calibration for offset and wear values.Ĭ) Inspection prior to machining to determine material allowance on castings.ĭ) Inspection after machining to determine parallelism and flatness values as well as location. 12 inches by 5 inches using a 3 inch fly cutter)Īutomatic Offset Setting Based On The Program - With macros, coordinate offsets can be set in each program so that setup procedures become easier and less error-prone (macro variables #2001-2800). 12 across and 15 down)į) Fly-cutting a surface, (e.g. For example:Ĭ) Angular patterns, any number of holes, at any angle, with any spacingĮ) Matrix Patterns, (e.g. Simple Patterns That Are Repeated- You can define and store repeated patterns with macros. Essentially, this is a custom canned cycle. Here, macro 2000 (P2000) does the work since it was designed to drill the clamp bolt hole pattern at the specified angle of A. Where nnn are the coordinates determined in Step a). Read the position coordinates from the machine display. If you discovered, after setup, that a fixture needs an additional clamp, and suppose that you programmed macro subprogram 2000 to drill the bolt pattern of the clamp, then you only need this two-step procedure to add the clamp to the fixture:Ī) Jog the machine to the X, Y, and Z coordinates and angle where you want to place the clamp. For instance, suppose a company uses a standard clamp with a standard bolt hole pattern. You can reserve tools for immediate situations that you did not anticipate in your application design. Tools For Immediate, On-Table Fixturing - You can semi-automate many setup procedures to assist the machinist. The examples are outlines and not complete macro programs. Here are a few examples of the applications for Macros. A macro statement can assign a value to a variable, read a value from a variable, evaluate an expression, conditionally or unconditionally branch to another point within a program, or conditionally repeat some section of a program. The possibilities are almost endless.Ī Macro is any routine/subprogram that you can run multiple times. Some possible uses are: families of parts, custom canned cycles, complex motions, and driving optional devices. Macros add capabilities and flexibility to the control that are not possible with standard G-code. NOTE: This control feature is optional call your HFO for information on how to purchase it.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |